Replace the cone burr: Baratza Sette 270Wi

Before you start

Tools

5 mm hex key (supplied)

Supplies

replacement cone burr (Baratza S1 cone burr for the Sette series (also sold with its holder))

Warnings

• Always unplug the grinder before you clean it. Source: Baratza Sette 270Wi manual v2.4 (Aug 2019, EN)
• Keep the burrs and the grind adjustment assembly out of water; they rust. Source: Baratza Sette 270Wi manual v2.4 (Aug 2019, EN)

Steps

1. Close the bean shutoff knob and press START to purge the beans left in the grinder.

   From the manual: “Rotate the bean shutoff knob to the CLOSED position”

2. Unplug the grinder.

   From the manual: “Remove the power plug from the power outlet.”

3. Turn the hopper counterclockwise until it stops and lift it off.

   From the manual: “Remove the hopper by rotating it counterclockwise until it stops”

4. Swing the adjustable portafilter hook out to one side.

   From the manual: “The adjustable portafilter hook must be swung to the side”

5. Turn the grind adjustment assembly past the coarsest setting to the blue triangle; it drops down and out.

   From the manual: “rotate the grind adjustment assembly beyond the coarsest setting to the install/remove indicator (blue triangle).”

6. Hold the adjustment assembly in one hand and pull or prise the cone burr holder away from it.

   From the manual: “grab the cone burr and holder with your other hand and pull/pry them apart.”

7. Pull the clear plastic funnel off the cone burr holder.

   From the manual: “remove the clear plastic funnel by pulling away from the cone burr holder.”

8. Fully loosen the bolt in the bottom of the holder with the supplied 5 mm hex key.

   From the manual: “fully loosen the bolt in the bottom of the cone burr holder”

9. Take the old cone burr off; if it sticks, rest the bolt in place unthreaded and tap the hex key on the bench to knock it free.

   From the manual: “tap the hex key against your work surface.”

10. Fit the new cone burr so the tabs on the holder sit fully in the slots under the burr.

    From the manual: “Reinstall the cone burr so that the tabs on the cone burr holder seat fully into the slots on the bottom of the burr.”

11. Refit the bolt and tighten it as far as it will go.

    From the manual: “Reinstall the bolt and tighten down as much as possible.”

12. Push the clear plastic funnel back on.

    From the manual: “Reinstall the funnel.”

13. Stand the holder burr-down on the counter and press the adjustment assembly firmly down over it until they join.

    From the manual: “firmly press the adjustment assembly down onto the cone burr and holder”

14. Line up the blue indicator on the assembly with the blue indicator on the right side of the grinder.

    From the manual: “Align the blue installation/removal indicator on the grind adjustment assembly”

15. Push the assembly gently upward and turn the black cone burr holder until it keys in and slides up.

    From the manual: “rotate the black cone burr holder (fig G) until the tabs and notches line up”

16. Keep pushing up and turn the blue tab toward the back of the grinder until the assembly clicks home.

    From the manual: “The adjustment assembly will click as it properly engages”

17. Refit the hopper: knob at 11 o'clock, three tabs in their slots, then turn it firmly clockwise until it clicks.

    From the manual: “line up the 3 hopper tabs with the slots in the top of the grinder.”

Sources

• Baratza Sette 270Wi manual v2.4 (Aug 2019, EN) Manual

Researched on 2026-09-23.

Published: the sentence is on the maker’s own page or in the maker’s own document.

Applies to

• Baratza Sette 270Wi